- 136 3607
- 133 3303
Beastie so far - 132 3292
Coming together nicely now Tail piece is in, various tail-plane bits and bobs. The tail rotor blades are on the wrong way round here (and remained so for a while) until I realised I had the belt on the wrong way. I noticied this long before firing up the engine, thankfully. - 136 3608
- 132 3294
Tail rotor The orange material you can see through the hole is the belt. The blades twist together, in opposite directions. This is how you point the helicopter. - 132 3280
Engine in the frame, closeup - 132 3295
Main drive wheel The belt goes back to the tail rotor. The grey spindle meshes with a drive wheel on the engine drive shaft. There is a shaft going up through these two wheels directly to the rotor hub. - 136 3609
- 132 3287
Rotor head and flybar The fly bar, I think, ,ostly balances the main blades. They are on a single bar whose pitch alters with the cyclic, but not the collective (I think, lots of "I think"'s here!). The bar is supposed to be near-perfectly balanced otherwise it causes really nasty vibrations in the rest of the machine. Rememeber, this thing is a huge spinning top, really. - 133 3340
Outdoors [1/4] - 133 3304
Clutch The silver drum in the centre of the picture is the clutch bell. Inside this is a clutch disc, which runs directly from the engine below it. It's designed to be fully diengaged below about 7000rpm and fully engaged above 10000rpm. The rotor blades operate at a fraction of this speed, not normalyl going faster than about 1700 rpm. - 132 3279
Engine in the frame - 132 3290
Tail rotor assembly This was a fiddly piece to put together. - 137 3753
Still in one piece Front view, it's been out flying a couple of times now - 137 3749
Fuel line arrangement This t-piece arrangement allows me to load/unload fuel to the tank without pulling the pipwork away from the engine. Just use the right fuel line clip to direct the flow to/from the tank. Similarly, the left clip allows me to inject after run oil without having to do fiddly stuff, or remove the engine. - 136 3610
- 132 3291
Tail rotor assembly The red coloured pulley is a two-piece item, a flange fits on one end, and it can go two ways round. The correct way si with the shorter end into the pulley, longer end outwards. Otherwise, as I discovered, there is about 2 to 3mm play in the tail rotor shaft. Not good. - 132 3281
Engine in the frame, other side - 132 3285
Rotor head bearings At this point, I only assembled one end of this piece. The bearing set in the bag fit onto the shaft with a collection of washers, spacers, bolts, loctite and so on. It's all a bit busy. Particularly sicne I forgot to put in a supporting piece rigth in the centre to had to disassemble the thing. - 133 3305
Gyro This is described by many as the "most cost effective" stabilisation gyro on the market at present. It's job: keep the machine pointing in the direction you want it to. In the old days, you would program a "revolution mix" into your radio which altered the tail rotor blade pitch according to what you were doing with the throttle/collective, the idea being that you could match the rotational energy being put out by the main rotors to make the tail rotor counteract it, and keep the machine steady. Technology these days simply measures the rotation and does what it needs to counteract it. Funky. This is what makes the difference between whirly-top-with-dangerous-bits and simply "dangerous". - 136 3620
- 136 3623
- 136 3618
- 136 3615
- 136 3622
- 132 3286
Look at the mess! - 132 3288
Flybar again - 136 3621
- 136 3616
- 132 3283
Assembling the rotor head These bits will eventually sit atop the swash plate. - 136 3619
- 137 3751
Camera mount Allows me to bolt a camera, or other things, to the side of the Helicopter - 136 3614
- 133 3330
So far... - 136 3617
- 133 3331
The body/canopy This will be it's ultimate shape. - 136 3611
- 132 3282
The engine The slot-shaped hole you can see is where the exhaust (muffler) pipe will attach, when it arrives. - 137 3756
Front view - 136 3613
- 133 3341
Outdoors [2/4] - 132 3277
Engine, closeup - 134 3463
Rear rotor servo Moved the servo from the front of the chassis to the tail boom to shorten the control rod - less chance of flexing - 133 3336
Busy busy There's a lot going on with this machine. - 133 3329
Rotor hub It's really busy up here - I can't imagine this thing spinning as fast as it will need to. - 133 3306
Digital servo The Gyro came with this servo. Because the tail rotor pitch is being computer controlled, and you want it to react fast, you have to use a fast servo. Better yet, you use a digital servo, which mostly means the servo PWM's the motor inside much much faster. This is a reasonably speedy digital servo. When it's going, it whines a bit, but I am pretty sure that's normal. - 136 3612
- 132 3278
Engine, other side - 133 3328
The exhaust It's shiny now. I'm sure that will change. The silicone pipe runninf from it is a fuel tank pressurisation aid. There's no fuel pump - a certain amount of exhaust gas is used to push the fuel into the carb of the engine. Quite neat, really. - 133 3339
I fired it up... So, I took it outside, just to fire up the engine. Nobody else around to take pictures, so this is after the event. They definately make good lawn mowers - notice all the grass and grass stains. I'm so far away from flying this thing (still practising on the simulator) but I thought it would be good to give the engine and mechanics some exercise before it does fly. These things are not quiet! - 134 3464
Rear rotor servo cabling - 133 3337
Wires/servos Much cabling. Notice how I had to trim some of the servo "horns" - they interfered with the ball-link attachments. - 133 3335
The electronics arrived All the servos are on, the receiver is mounted and hooked up. - 132 3276
The engine OS 32 helicopter engine. Here it is with the Raptor cooling fan attached, basically a centrifugal fan. - 133 3327
It's looking a bit big Note we have an exhaust (muffler) now also. - 133 3338
The radio I decided to start small. A 6-channel JR transmitter. It came with the servos and a 7-channel receiver. - 132 3273
Getting started When I remembered I wanted to take pictures of the construction, this is far as I was already. - 147 4775
- 133 3332
Rear view - 133 3342
Outdoors [3/4] - 147 4776
- 132 3274
Side view - 133 3326
Progress! With the main rotor blades on, it's starting to look like a helicopter now. - 132 3275
The swash plate This little device is freaky. In a nutshell, the pitch of the blades varies through their rotation, according to the motions of the aileron/elevator servos (called cyclic on a helicopter) and the collective pitch. It's all a bit mad and I onyl slightly understand it so far. - 134 3462
In flying shape - 150 5072
- 147 4725
- 147 4777
- 133 3343
Outdoors [4/4] - 147 4738
- 147 4752
- 147 4771
- 147 4724
- 133 3333
Size comparison The universal measuring device: A Coke can. - 133 3334
Size comparison - 150 5071
- 147 4757
- 147 4790
- 148 4803
- 147 4786
- 147 4782
- 147 4739
- 147 4750
- 147 4797
- 147 4769
- 147 4773
- 147 4758
- 147 4737
- 147 4727
- 147 4780
- 147 4785
- 147 4779
- 147 4756
- 147 4783
- 147 4774
- 147 4789
- 147 4759
- 147 4743
- 147 4755
- 147 4760
- 147 4729
- 147 4733
- 147 4753
- 147 4781
- 147 4791
- 147 4742
- 147 4768
- 147 4734
- 150 5013
- 147 4751
- 147 4792
- 147 4744
- 147 4770
- 147 4726
- 148 4802
- 147 4732
- 150 5035
- 150 5020
- 147 4787
- 147 4740
- 147 4800
- 147 4754
- 150 5014
- 147 4748
- 147 4798
- 147 4749
- 150 5023
- 147 4728
- 147 4736
- 147 4735
- 147 4784
- 150 5022
- 147 4731
- 133 3368
- 150 5036
- 150 5033
- 148 4801
- 147 4761
- 147 4741
- 150 5070
- 147 4796
- 147 4747
- 150 5045
- 150 5017
- 150 5046
- 150 5047
- 150 5019
- 150 5044
- 147 4746
- 147 4730
- 147 4793
- 150 5015
- 150 5032
- 150 5038
- 150 5048
- 150 5016
- 150 5028
- 133 3364
- 150 5029
- 150 5041
- 147 4799
- 150 5042
- 150 5030
- 150 5043
- 147 4745
- 150 5021
- 150 5064
- 150 5049
- 150 5018
- 133 3362
- 150 5069
- 150 5024
- 150 5025
- 147 4764
- 150 5059
- 147 4762
- 150 5061
- 150 5063
- 133 3363
- 150 5039
- 133 3367
- 150 5060
- 147 4763
- 133 3360
- 133 3357
- 150 5040
- 150 5062
- 133 3365
- 133 3358
- 150 5066
- 150 5068
- 150 5065
- 150 5067
- 133 3359
- 150 5050
- 150 5057
- 133 3366
- 133 3361